JACKYLED Waterproof LED Strip Connectors for Patio and Deck RGB Accent Lighting, 10mm 4-Pin Outdoor Kit
JACKYLED Waterproof LED Strip Connectors for Patio and Deck RGB Accent Lighting, 10mm 4-Pin Outdoor Kit
Couldn't load pickup availability
Why you'll love it
- Solderless snap design removes the need for a soldering iron, making it accessible to beginners
- Dual-purpose kit combines L-shape corner connectors and straight extension couplers in one purchase
- Orientation-agnostic design works regardless of which side the RGB+ pad is on, preventing install mistakes
- Compatible with the most common 10mm 4-pin SMD 3528/5050 strips including waterproof versions
- Bulk 20-pack with 2 bonus couplers and printed instructions reduces the need to re-order mid-project
- Water-resistant rating allows the same connectors to be used for both indoor and outdoor runs
- Works with Lepro LED strips when other brands like JACKEYLED did not
- Holds tight with little teeth that clamp down on contacts, better than other brands tried
- Relief of finding connectors that actually work after failures with competitor products
- Works flawlessly even with offset 3-pin 10mm strips (e.g., Monster brand) using 4-pin 10mm connectors
- Second-time purchase shows repeat satisfaction
- Easy to use even without prior experience with small electronic flexible circuits
- Having extra clips and connectors included made installation smoother
Perfect for
- Joining two LED strip runs around a 90-degree corner without cutting or soldering
- Extending an LED strip run along a straight line to reach farther distances
- Repairing a broken or disconnected section of an existing 10mm LED strip
- Completing a full-room RGB strip installation including corners and room wrap-arounds
- Connecting waterproof outdoor LED strips for patio or deck accent lighting
- Fixing accidentally cut LED strips
- Repairing torn Govee LED strips after project mistakes
- Creating a U-shape out of LED strips for a bookcase
- Cornering LED strips around TVs (especially with offset 3-pin Monster brand strips)
- Rescuing cut-off sections of TP-Link Tapo L900 LED strips for reconnection
- Cabinet LED installation
10MM 4-Pin Led Strip Connectors Kits - DIY Project Essential
Before purchase, please confirm that your led strip lights are 4-pin with 10mm width, if you are not sure , please contact JACKYLED Online Service with pictures or check with strip light supplier to get the width & pins
Two ways to connect
Why choose JACKYLED LED Connectors?
The connector set for RGB LED light strips comes with easy-clasp connector clips and 90 degrees L shape PCB boards. You can connect with light strips directly without any tools or welding operations. The unwired design ensures a gapless layout when you need to turn your LED strips around corners. Compatible with both ordinary and waterproof 4-pin light strips.
Package Includes:
10 pcs L shape RGB sheets --For corner connection
22 pcs 4-pin connector clips --For direct connection with led strips
10pcs L shape RGB sheets
Thoughtful and considerate to ensure the smooth progress of your DIY project
ONLY compitiable with 10 mm 4 Pin Strip Lights, Not 8mm, 2pin, 3 pin
22 pcs 4-pin connector clips
Cost-effectiveness price with enough quantity to clip with long LED strips
ONLY compitiable with 10 mm 4 Pin Strip Lights, Not 8mm, 2pin, 3 pin
Corner Connections
2 clips with 1 L shape sheet, perfect combination to connect with cornner area of wall, bed, shelf, gaming table etc
Extended Connections
2 clips to connect LED light strips directly, perfect to create charming atmosphere
Installation Instructions:
1.Open the clip on the side
2.Slid the 10mm 4pin LED light strip inside the clip underneath the contact prongs, if not 10mm 4 pin, it can't insert sucessfully
3.Make sure the side of the strip aligns with the "+ -" polarity, Then, close the wire clip
Product Information
Dual Purposes: This LED strip connector kit comes with detachable L sheets and straight couplers, perfect for both 90 degree corner connections and extensions along a straight line. Total 22pcs connector clips and 10pcs L Shape connectors For All 4 Pin Light Strips: Work with any 4-pin 10mm (0.39in) wide SMD 3528/5050 multicolor LED flexible strip lights, whether they are waterproof ones or non-waterproof lights for indoor use. Solderless Solution: Create a quick shunt, solid connection without the hassle of soldering. Just slide the light strip under the connector's pins and snap the clip. (Tip: Please do not pry up the metal pins. Doing so may cause poor contact.) Go Both Left and Right: No matter in what orders are the RGB+ marked on the connectors, the connection work as long as the + of the light strips on both sides are aligned. You Get Extra: Apart from 10 pieces of L boards and 20 connector clips in this 10-pack, 2 extra couplers are included, as well as detailed instructions both printed and online. If you need any help when using the connectors, please feel free to contact our online customer service team.
Features & Specs Indoor Outdoor Usage Indoor Additional Features Only work with 10mm 4pin led strip lights, Total 32 pcs Light Source Type LED Power Source Corded Electric Light Color RGB Voltage 12 Volts Wattage 72 watts Water Resistance Level Water Resistant Style Color White Theme Indoor Occasion Christmas Product Style simple Measurements Number of Light Sources 60 Item Weight 0.07 Pounds Number of Items 20
Frequently Asked Questions
Can I use these connectors on my waterproof outdoor LED strip around the deck?
Yes. The connectors are compatible with both waterproof and non-waterproof 10mm 4-pin SMD 3528/5050 strips, so they work for outdoor deck and patio accent runs as long as the joint is sealed from standing water.
Will the connectors hold up to rain on a patio or covered porch?
The connectors themselves are water-resistant and tolerate splashes and humidity. For joints exposed to direct rain, adding a small bead of silicone over the joint is recommended to keep water out of the contact area.
Can I use this kit to run LED strips around a pool deck perimeter?
Yes, this is a common use. The L-shape corners handle the 90-degree turns around the deck framing, and the straight couplers extend the run to the full perimeter length.
Is this kit portable enough to bring along for a camping or tailgate LED setup?
Yes. The kit is small, lightweight, and requires no tools, so you can toss it in a camping bin and use it to repair or extend 12V LED strip setups at a campsite or tailgate.
Can I use it for an outdoor dining area with a permanent strip install?
Yes. Once the connector is closed on a waterproof strip and optionally sealed with a little silicone, it will hold up through a full outdoor season under a covered dining area.
Will the connector corrode if it sits in a humid outdoor environment?
The metal pins are tin-plated for corrosion resistance. For long-term outdoor use, sealing the joint with silicone or heat-shrink is the standard practice to keep moisture away from the contact pads.
Can I extend a strip run across a long fence line or pergola?
Yes. Use the straight couplers to daisy-chain multiple strip runs, and the L-shapes to turn corners at the post tops or pergola beams, all without any soldering.
How does this compare to buying a pre-made outdoor LED extension cable?
Pre-made extension cables are usually a fixed length, while these connectors let you join strips of any length and turn corners on the fly, which is more flexible for an outdoor layout that is rarely perfectly straight.
Can I take down the outdoor strips in winter and reuse them next year?
Yes. Because the joints are snap-on and not soldered, you can open the clamps, store the strips indoors over winter, and re-install the same setup next season without buying new hardware.
Will the connectors work for a backyard kitchen or bar counter LED install?
Yes. Outdoor bars and outdoor kitchens often need corners at the counter edges, which the L-shapes handle cleanly, and the waterproof rating keeps the joint safe from splashes.
Can I power a long outdoor run from a single 12V supply using these connectors?
Yes, but for very long runs you should follow standard 12V LED voltage-drop guidance and inject power at intervals. The connectors themselves do not add meaningful resistance, so they will not be the limiting factor.
Are the connectors safe to leave out in freezing temperatures?
Yes. The plastic and PCB materials handle sub-freezing temps fine when the strip is not actively flexing. Avoid bending the connectors hard in extreme cold to prevent cracking the board.
Do I need to bring any tools to the outdoor install site?
No tools are required. Bring the kit, the strips, and optionally a small tube of silicone for sealing. The clamp is operated by hand.
Can I use these to repair a strip that got cut by a lawn tool or weed whacker?
Yes. Cut the damaged section back to clean copper, splice in a short replacement piece with the straight couplers, and the strip is back in service with no soldering required.
Is the kit small enough to pack in an RV or camper LED toolkit?
Yes. The whole 32-piece kit fits in a small zip bag, so it is easy to keep on hand in an RV, boat, or trailer for quick field repairs to 12V strip lighting.
Can I use these on a strip mounted under a hot tub or spa lip?
Yes, as long as the strip itself is rated for that environment. The connectors are passive and tolerate the same temperature range as the strip, and a silicone seal over the joint is recommended near splashing water.
How do I install these LED strip connectors without soldering?
Cut your LED strip to the marked cut line, peel back a small section of the adhesive backing to expose the copper pads, slide the strip under the pins of the connector or L-shape board with the pads aligned to the four contacts, and press the snap clamp down firmly until it clicks closed. The teeth bite into the copper pads to complete the circuit.
Can these connectors join two strips that were cut on different ends?
Yes, as long as both strips are 10mm wide 4-pin SMD 3528/5050 RGB. The bidirectional RGB+ alignment means the connector works regardless of which side the RGB+ pad lands on, so you do not need to worry about strip orientation when joining the two pieces.
What should I do if my LED strip does not light up after installing the connector?
Open the clamp and check that all four copper pads are fully exposed, clean, and aligned under the pins. Press the clamp down firmly again until it clicks. If the strip still does not light, try the other end of the strip in the connector to rule out a reversed orientation issue, even though the design is bidirectional.
Will this work with Govee, Lepro, TP-Link Tapo, and Monster brand LED strips?
Yes, as long as the strip is 10mm wide with 4 pins and uses SMD 3528 or 5050 RGB chips. The kit is confirmed to work with Govee, Lepro, TP-Link Tapo L900 series, and even offset 3-pin 10mm Monster brand strips when joined with a 4-pin 10mm connector. Verify your strip width and pin count before ordering.
Is this connector compatible with 8mm LED strips or COB / FCOB strips?
This specific kit is for 10mm 4-pin strips only. 8mm strips, FCOB strips, and 2-pin or 3-pin configurations are a different size and require a different connector variant, which is available separately in the same product line.
What is included in the box and what do I need to buy separately?
The kit includes 10 L-shape corner connector boards, 20 straight connector clips, 2 bonus straight couplers, and printed installation instructions, for 32 pieces total. You will need to supply your own 10mm 4-pin RGB LED strip and a compatible 12V power supply, neither of which is included.
Are these connectors safe and reliable for long-term use?
Yes. The connectors are made from standard PCB material with tin-plated contact pins and plastic snap clamps. They are passive components that draw no extra current, run cool under normal 12V LED loads, and are designed for repeated opening and closing without losing grip strength.
Will using a connector dim or discolor my LED strip at the joint?
When the clamp is fully closed on clean copper pads, the electrical contact is solid and there is no perceptible dimming or color shift at the joint. If you notice any dimming, it usually means a pad is not fully seated under the pin, and re-clamping the connector resolves it.
What is the difference between a snap-down solderless connector and a soldered LED strip joint?
A soldered joint uses a hot iron to melt metal onto the copper pads, which creates a strong permanent connection but requires skill, a soldering iron, and a safe workspace. A snap-down connector uses a mechanical clamp to bite into the same copper pads, creating a solid connection in seconds with no heat, no tools, and no permanent modification to the strip.
